Automatic Translations (Powered by Powered by Google):
Afrikaans Arabic Belarusian Bulgarian Catalan Czechoslovakia Cyprus Germany  Spanish  Ethiopia Persian Finnish French Irish Galician Hindi Croatian Hungarian Icelandic Italian Hebrew Japanese Korean Italian Latvian, Lettish Macedonian Malay Maltese Dutch Norwegian Polish Portuguese Romanian Russian Slovak Slovenian Albanian Serbian Swedish Swahili Thai Tagalog Turkish Ukrainian Vietnamese English
FreeWeldingForum.com Welding Forum Community presented by LONGEVITY  
+ Reply to Thread Share
Results 1 to 7 of 7

Thread: Waste Veg Oil System

  1. #1
    Charley Davidson's Avatar
    Charley Davidson is offline Senior Member
    Join Date
    Jul 2010
    Location
    Murfreesboro, Tn
    Posts
    723
    Images
    25
    Thanks
    3
    Thanked 16 Times in 15 Posts

    Waste Veg Oil System

    Here's some pics and explanation of my WVO system

    In this pic you see the 80 gallon clean/processing tank made out of SS. It has about 30 feet of 1/2" titanium line coiled in it for hot water from the diesel fired boiler to heat the tank. The boiler is a Pro Heat and sitting right below the red expansion tank made out of an air tank. There is a hydrolic (sp) pump that pumps the oil up to and drives the centrifuge once the oil reaches about 140.

    The Pro Heat also provides hydronic heat for my bus & hot water, it can also be plumed into my engine for pre heating it in cold weather but not done at this time. The pump and tank has several 3 way valves so I can pump from anywhere to anywhere.
    Name:  wvo system.jpg
Views: 41
Size:  65.3 KB

    This is the centrifuge that spins at about 7,000 rpm slinging the dirt to the wall and caking there it also suspends water as long as it is spinning.
    Name:  centrifuge.jpg
Views: 41
Size:  71.0 KB
    Millermatic 140
    Thermodynamics 190C plasma cutter
    Plasma Trace (custom built by me)
    Victor O/A torch HVAC size
    Craftsman 15" floor model drill press
    Craftsman 6" metal lathe
    Wilton horizontal band saw
    Porter Cable 60 gallon compressor
    Clarke parts washer
    Craftsman 10" table saw
    Ryobi 8 1/2" sliding miter saw
    Homemade bench top english wheel
    Homemade plannishing hammer
    Tons of hand power tools
    1500 sq ft shop
    & an over active imagination

  2. The Following User Says Thank You to Charley Davidson For This Useful Post:

    rustycase (04-19-2011)

  3. #2
    Gadget's Avatar
    Gadget is online now Moderator
    Join Date
    Nov 2007
    Location
    Michigan
    Posts
    4,560
    Images
    138
    Thanks
    72
    Thanked 123 Times in 114 Posts
    Pretty cool Charley.
    Units owned
    Longevity WeldPro LS200PI (IGBT)
    Force Cut LP80 plasma cutter
    Longevity auto dark welding helmet

    Atlas 10x36" lathe
    Craftsman 5HP 30 Gal compressor
    Home made CNC router/plasma/hot wire foam cutting table powered by Longevity Force Cut LP80
    Home built aluminum foundry, HF 4x6 bandsaw, O/A torch

  4. #3
    KHK's Avatar
    KHK
    KHK is offline Moderator
    Join Date
    Oct 2008
    Location
    Chicago suburbs
    Posts
    2,548
    Images
    88
    Thanks
    0
    Thanked 52 Times in 50 Posts
    Is this a mobile unit? Do you have any drawings showing the movement of the oil?
    keith
    The older the Boys, the more expensive the TOYS
    Previously Owned equipment;
    lot's
    Current equipment;
    3HP Speedair air compressor, Wilton drill press, Craftsman 10x36 lathe, 10 ton hydrolic press, Portaband band saw, OA torch, Small home brew CNC machine, powered by my 200PI
    2 Longevity autodarking helmets
    160d MIG
    WeldAll 200PI

  5. #4
    Charley Davidson's Avatar
    Charley Davidson is offline Senior Member
    Join Date
    Jul 2010
    Location
    Murfreesboro, Tn
    Posts
    723
    Images
    25
    Thanks
    3
    Thanked 16 Times in 15 Posts
    I have one somewhere but don't know where but basically I pump oil into the big ss tank using the pump you see on the floor to the left, it has 2 3way valves on it one at suction side and one at pressure side. I turn on the pro heat and when it gets hot enough I start the pump pumping now from the tank up to the centrifuge, then the oil just gravity feeds back down into the ss tank. I usually run it continuous overnight, it will do 60 gallons an hour so by letting it run for 8 hours it gets it really clean. I can then either pump it into the tank in the engine compartment that serves as my fuel tank or into a storage tank in the front bay. I have about 250 gallons of oil right now.
    Millermatic 140
    Thermodynamics 190C plasma cutter
    Plasma Trace (custom built by me)
    Victor O/A torch HVAC size
    Craftsman 15" floor model drill press
    Craftsman 6" metal lathe
    Wilton horizontal band saw
    Porter Cable 60 gallon compressor
    Clarke parts washer
    Craftsman 10" table saw
    Ryobi 8 1/2" sliding miter saw
    Homemade bench top english wheel
    Homemade plannishing hammer
    Tons of hand power tools
    1500 sq ft shop
    & an over active imagination

  6. #5
    KHK's Avatar
    KHK
    KHK is offline Moderator
    Join Date
    Oct 2008
    Location
    Chicago suburbs
    Posts
    2,548
    Images
    88
    Thanks
    0
    Thanked 52 Times in 50 Posts
    Good info, Thanks!
    keith
    The older the Boys, the more expensive the TOYS
    Previously Owned equipment;
    lot's
    Current equipment;
    3HP Speedair air compressor, Wilton drill press, Craftsman 10x36 lathe, 10 ton hydrolic press, Portaband band saw, OA torch, Small home brew CNC machine, powered by my 200PI
    2 Longevity autodarking helmets
    160d MIG
    WeldAll 200PI

  7. #6
    ISKI's Avatar
    ISKI is offline Senior Member
    Join Date
    May 2010
    Location
    CT
    Posts
    476
    Images
    54
    Thanks
    0
    Thanked 5 Times in 5 Posts
    Nice setup. I'm looking into what I will need for a conversion. So far I have the truck and a diesel engine in the garage.
    Iggy
    "Man is the best computer we can put aboard a spacecraft ... and the only one that can be mass-produced with unskilled labor"
    Apollo 11 W.V. Braun

    Have ForceCut80I, Precision TIG 185, Ideal Arc 250, Oxy-Acetylene, Tig welding Chamber, 14 Ton pipe bender, 20 Ton press, Electric sheet metal shear, 12 inch- 0.125 Shear, 12 inch Metal Band Saw, Power Hack Saw, Abrasive Chop Saws, 2 Mills, 5 Lathes, and lots of other items

  8. #7
    rustycase's Avatar
    rustycase is offline Senior Member
    Join Date
    Mar 2011
    Location
    Left coast
    Posts
    343
    Images
    27
    Thanks
    26
    Thanked 4 Times in 4 Posts
    That's great, Charley!
    I was about to build a WVO system til the tax collector towed my two diesel vehicles... something abt parking in the wrong place for too long???
    Had a pooqwat and a vovo. both w turbos.
    But they gone now.
    Gonna try alcohol when I get the plumbing project done.
    Best
    rc

    ---------- Post added at 07:04 PM ---------- Previous post was at 07:03 PM ----------

    That's great, Charley!
    I was about to build a WVO system til the tax collector towed my two diesel vehicles... something abt parking in the wrong place for too long???
    Had a pooqwat and a vovo. both w turbos.
    But they gone now.
    Gonna try alcohol when I get the plumbing project done.
    Best
    rc
    Longevity Stickweld 140 Lunchbox Baby!
    Redi Arc & Craftsman AC boxes
    200P 3 in 1
    Harris gages/Victor & Smiths torches
    101.07301 project
    Large pile of saws & drills
    Wheel barrow full a sanders N' grinders
    truckloads of woodworking tools
    the paint pumps, ladders and stuff
    rock n mud tools & plumbin stuff
    Lapidary thangs
    mekanik tools
    & I am a pathological liar and functional illiterate.

+ Reply to Thread Share

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
 
 
www.longevity-inc.com | About us | Products | Rentals | Resources | Dealers | Order Status | Contact us | Help & Faqs | Site Map